Quality metal roofing installation requires specialty tools to get the job done right. Whether its cutting, seaming or bending our metal panels, we offer top-quality metal roofing tools that work hard, make installation easier, and withstands real-life use on the job.

Hemming Tools

    Drip Edge Hemming Tool

  • Reinforced steel plates
  • Ideal fit for 1.5” folded bends
  • Makes uniform 18” bends
  • Ergonomic handle
  • Coated contact surfaces to protect metal panel finishes from marring or scratching
  • For use on up to 22-gauge steel
  • 18” w x 17”–1.5” lip
  • 4.6 lbs

    Single Handle Hemming Tool

  • High-quality steel construction
  • Low side hemming
  • Zinc-Chromate Plated
  • Rubber grip handle
  • 1-1/2” depth in sizes 11.25”, 15.25”, 17.25”, 19” and 20”

    7” Turn-Up Tool

  • Zinc-chromate plated
  • Rubber grip handle
  • Tapered side reliefs
  • 3/16” gap
  • 1-3/4" turn-up depth
  • 7/8” turn-down depth
  • Available sizes: 2” x 7” and 2” x 8-1/2”

    Wide Handle Hemming Tool

  • High quality steel construction
  • Zinc-chromate plated
  • Parallel rubber grip handle
  • 1/8" gap
  • 1-1/2" depth
  • Temperature resistant from -90º to 200º+ F
  • Can be used on panels up to 23" wide
  • Available for EMax, PBRMax, and VMax profiles


Crimpers

    90º Hand-Crimper

  • Steel with state-of-the-art ceramic finish
  • Superior resistance to wear, corrosion, heat and chemical exposure
  • Rates for 22 gauge steel
  • Handles 28.5” fully opened
  • 9” crimp area
  • 7.4 lbs

    180º Hand-Crimper

  • For use with 90º hand crimper to prepare for roof seamer
  • Steel with state-of-the-art ceramic finish
  • Superior resistance to wear, corrosion, heat and chemical exposure
  • Rates for 22 gauge steel
  • Handles 28” fully opened
  • 5” crimp area
  • 5.1 lbs

    Modulation Clamp

  • For use with standing seam panel
  • Dipped nylon-powder coating to protect roof panel finish
  • 6” x 11”
  • 2.5 lbs

    5” Offset Seamer

  • Offset handle provides extra leverage
  • Light-weight aluminum blades
  • Easily interchangeable blades
  • Bends soft materials with ease
  • 5” x 2” blades x 2-1/4” throat depth
  • Also available in 9” and 15”


Nut Setter and Screw Driving Tools

    #2 Philips Driver Bit

  • 2-3/4”
  • Combo #3 Philips/#2 Square also available

    #2 Square Driver Bit

  • 1-5/16”
  • Combo #3 Philips/#2 Square also available

    Spring-Clip Hex Nut Setter

  • Non-magnetic
  • Pressure long spring clip
  • Superior driving
  • Reduces paint removal from fastener head
  • 1/4" standard
  • 5/16” and 3/8” available

Snips

    9-3/4” Compound Action Straight and Left Cut Aviation Snips

  • Cuts left from tight curves to straight
  • Cuts low carbon cold rolled steel
  • Non-slip serrated jaw of tough molybdenum steel holds material firmly and uniformly spreads cutting force across blade edge
  • Withstands strain of cutting heavy stock
  • Spring-action for fast effortless feed
  • Non-slip textured grips and safety latch
  • 1-3/8” cut length
  • 40 lbs

    9-3/4” Compound Action Straight and Right Cut Aviation Snips

  • Cuts right from tight curves to straight
  • Cuts low carbon cold rolled steel
  • Non-slip serrated jaw of tough molybdenum steel holds material firmly and uniformly spreads cutting force across blade edge
  • Withstands strain of cutting heavy stock
  • Spring-action for fast, effortless feed
  • Non-slip, textured grips and safety latch
  • 1-3/8” cut length
  • 40 lbs

    9-1/4” Metalmaster® Offset Straight and Left Cut Aviation Snips

  • Cuts left and straight
  • Offset blades keep hands clear of metal
  • Molybdenum steel non-slip serrated jaw for compound lever action
  • Able to cut heavy stock and tight curves
  • Spring-action allows for fast effortless feed
  • Non-slip textured grips and safety latch for superior control
  • Cuts low carbon cold rolled steel
  • 1-1/4” cut length
  • 40 lbs

    9-1/4” Metalmaster® Offset Straight and Right Cut Aviation Snips

  • Cuts right and straight
  • Offset blades keep hands clear of metal
  • Molybdenum steel non-slip serrated jaw for compound lever action
  • Able to cut heavy stock and tight curves
  • Spring-action allows for fast effortless feed
  • Non-slip textured grips and safety latch for superior control
  • Cuts low carbon cold rolled steel
  • 1-1/4” cut length
  • 40 lbs


    14” Lightweight Aluminum Handle Tinner’s Snip

  • Sleek head design reduces cutting effort
  • Large, wide handle loops comfortably fit all hand sizes, including gloved hands
  • Longer handle length and rounded head design improve cutting leverage
  • Strong and durable lightweight aluminum construction
  • Easy and quick blade replacement
  • 3-1/4" Cut Length
  • 1.4 lbs

    TurboShear® HD Cutting Tool Drill Attachment

  • Fits corded/cordless drill you already own
  • Make fast, straight, curved or square cuts
  • Wide opening for high or low speeds
  • Telescoping drill clamp adjusts to length and width of drill sizes
  • Clamp collar allows 360º rotation
  • Long-lasting carbon steel blades
  • Can cut up to 18ga steel, 20ga non-hardened carbon steel and stainless steel, 14ga aluminum, and .100” copper

Contact Us

  • Main Location: 364 Recker Hwy, Auburndale, FL 33823, USA

  • Phone: +1 813-754-0771

  • Email: info@jnjwelding.com

  • Manufacturing Sites: View our Google Map

Auburndale Location

Panama City Location

Follow Us